A2D Solutions - TVProRacks : DDB Unlimited : DDB Unlimited POD-1020

DDB Unlimited POD-1020

Pole,Wall,or Pad Mount Enclosure

DDB Unlimited

The POD-1020 is a compact totally weatherproof (NEMA 4X) outdoor enclosure that offers 20" of usable depth & accommodates up to 10.5 vertical inches of 19" rack space. Pre-drilled into the back wall and covered with a 3"x3" apron are three connector hole patterns (cut outs, 2 for RF & 1 for power). Each of the three connector cut outs comes with it's own removable access plate. The access plates may be left in place if not needed or they may be removed and an RF connector or a 7 pin power connector may be installed into their place.

This design makes this unit very portable. Once you install the three connectors, connect their associated wiring to your unit & rack mount your unit, you can close the door and lock it. From then on the RF and power will be accessible through the three connectors in the rear of the POD-1020. A small fan may be mounted up inside the 3"x3" apron if ventilation is needed. The POD-1020 can be wall, floor or pole mounted.

3" Rear Apron	Shields rear connectionsfrom the rain (RF & Power)
Pre-drilled access holes	3-cut out support: 2 - typeN or UHF chassis mount connector's 1-7 pin weatherproof connector
Finish	Cream colored, textured,powder baked on paint
Rails	Two standard & alodinecoated, on EIA 19"
Doors	Front door secured withnon-intrusion lock
Seals	Neoprene slotted gasketseals top cover / Aluminum filled 13/16" gasket seals door

Top Of Page

Specifications

General
Weight	31 lbs. assembled
Doors	one - secured withnon-intrusion lock, two keys supplied Door Seal: 13/16" aluminum filledgasket
Material	125 ALUMIFLEX / RFproperties: nonferrous.
Finish	Cream, textured, powderbaked on paint.
Top Cover Seal	Neoprene slotted gasket
Exterior Screws	Stainless withNEMA washers & nylon locking nuts
Racking Specifications
Rails	Two standard (.125 ALUMIFLEXmaterial) Alodine coated 19" racking holes tapped to 10 x 32 threads Note: Rails come pre-mounted, which allows your equipment'shandles room to protrude out in front a distance up to 1 1/4 inches (ifthis is acceptable). Or, if desired, rails can be mounted at any depth. (Customerdrills four new mounting holes & mounts rails with the suppliedextra screws & lock nuts)
Spacing	19" EIA STANDARD
Useable Height	10 1/2 inches
Useable Depth	20 1/2" minimum/ 21" maximum
Door Opening Clearance
Height	10 1/2 inches
Width	21 7/8 inches
Exterior Cabinet Dimensions
Main Body	Width: 22 1/4 inches Height: 10 3/4 inches Depth: 25 1/4"
Exterior Cabinet Dimensions
Door	Width: 23 1/8 inches Height: 11 5/8 inches Depth: 1 3/4 inches
Total Space Occupied	Width: 23 2/8inches Height: 11 3/4 inches Depth: 25 1/2 inches
Inside Clearance - Less Rails
Width	21 7/8 inches
Height	10 1/2 inches
Depth	22 1/4 inches
REAR POWER CONNECTOR HOLE
Hole size:	One .858" diameter hole withtwo .142" mounting holes / spaced 1.22" apart
Description:	Supports one male 7 pinpower connector (Allied part # T-3106-000 (weatherproof - male) mateswith female 7 pin power connector (Allied Part # T-648-000(weatherproof - female))
Location :	Under the rearapron, in the center of the rear panel
REAR RF CONNECTOR HOLES
Hole size:	Two .641 diameter holes eachwith four .125" mounting holes / spaced .718" sq.
Description:	Supports two chassis mounttype N or UHF connections
Location :	Both holes arelocated under the rear apron, one on the left side & one on rightside of the rear panel
Ratings
NEMA	Class 250 Type 4
Paint Tested	500 Hour saltspray 500 hour immersion
Warranty
Period	Seven Years -Unconditional

Top Of Page

Accessory Options

R-2-10:	Two extra 62 " rails andmounting hardware
SCR-432:	Rail Screws (4) 10x32

Top Of Page

Climate Control Options

Air Conditioners	viewall options
Heater Options	viewall options
AC & DC Fan Kits	viewall options

Mounting Notes

Standard

The 3" wide by22 1/4" hang down apron, runs horizontally & is located at the topof the back panel. The matching 1 1/2" by 22 1/4" wide bent up mountingplate, runs horizontally & is located at the bottom of the backpanel.

Customer drills the needed mounting holes into the 3" hangdown apron & the 1 1/2" bent up mounting plate.